Industrial & Scientific From USA Knifemaker on Amazon

Nickel Ball Time @ 100°F: 7 - 9 seconds, Flash Point: > 275°F

Parks 50 is considered a fast oil. Many times a quench oil is described in seconds quenching using a Nickel Ball test. The Nickel Ball quench time is 7-9 seconds.

Note: All shipping will be via UPS ground. No international shipments.

Protect your knife blades from dulling with these cardboard knife sleeves.

Great for sharpening services to purchase in bulk

Available in 1", 1.4", 1.75", 2.5" or a variety pack of all widths

Parks AAA is considered a medium to medium fast oil. Many times a quench oil is described in seconds quenching using a Nickel Ball test. The Nickel Ball quench time is 9-11 seconds.

Typical steels to use with this quench oil formula include: O1, 5160, 1080, 1084. Many others steels using “medium” speed (there is no hard and fast definition of “fast” or “medium”) will be appropriate with this quench oil.

Note: All shipping will be via UPS ground. No international shipments.

Appearance: Light Amber Oil, Viscosity @ 100°F: > 5.8 cSt

Nickel Ball Time @ 100°F: 7 - 9 seconds, Flash Point: > 275°F

Note: All shipping will be via UPS ground. No international shipments.

Parks AAA is considered a medium to medium fast oil. Many times a quench oil is described in seconds quenching using a Nickel Ball test. The Nickel Ball quench time is 9-11 seconds.

Typical steels to use with this quench oil formula include: O1, 5160, 1080, 1084. Many others steels using “medium” speed (there is no hard and fast definition of “fast” or “medium”) will be appropriate with this quench oil.

Note: All shipping will be via UPS ground. No international shipments.

This foil is sold by the foot so if you order 10, you will get 10 feet by 20" wide.

This tool wrap is .0020" thick and is 20" wide. A single wrap will do. Use this foil to wrap your knives before heat treating to protect them from damage to decarb or scale.

Double over all the seams and pound them shut with a hammer. This stuff will cut you like a razor! Be careful when you handle it.

We bought some big planks of Aluminum (big) and cut them into sets of plates. Use these as quench plates for your air hardening steels instead of air or even oil hardening steels.

In use, place your knife from the oven, still in the pouch between the plates. Press flat with your hand. You don't need much pressure at all. Shoot compressed air all around in between the cracks. Your knife should be cool to the touch in just a minute or so

I've heard of some guys putting their plates in the freezer before quenching. If get condensation on the plates and then place a burning hot packet of steel in contact with the water, you are going to have a dangerous out gassing of scalding steam. Best to avoid that. Keep you plates dry

Hole and slot size is .187"

Made in China

4.5" x 1.25" handle material area

Excellent for Cleaning Rusty Surfaces and Welding Burns and for Removing Machine Marks.

Greaseless compounds have a water soluble adhesive base, which dries hard if left exposed to air. To prevent this, open tubes should be resealed or wrapped in a damp cloth. Warm weather softens greaseless compounds- sometimes excessively. To harden compound, store under refridgeration or put unopoened tubes in cold water prior to using.

Satin-Glo Compound is easily applied to loose or tight sewed buffs, hard felt or cloth polishing wheels and small bobs. This allows extreme flexibility for the operator when finishing articles that have flat or rounded surfaces as well as irregular, restricted and recessed areas.

These are 70 duro polyurethane small contact wheels that will fit into the small wheel attachment we sell seperately. These wheels will cost you approximately 1/3 less than the vulcanized rubber small roller wheels we also sell.

OAL is 3.125"

Note: all wheels are shown for size purposes. You are purchasing 1 wheel.