Patio, Lawn & Garden From Swimables on Amazon

Installation: Begin by removing the old circuit board by shutting down all power and opening the top of the heater to have access to the old board. Unplug the membrane pad from the board and remove the wire connectors connected to the old board.

Installation(2): Unscrew the 4 screws holding the board in place. This will allow you to take the old board completely out.

Installation: Simply remove the existing air release assembly by unscrewing the small bottom plastic connection. Take your new Swimables Air Relief Gauge Assembly and thread it into the same place that was removed. Be sure to release the air pressure once the air relief assembly is installed

Compatibility: This air relief assembly is designed to work with all Jandy Series Model DEV (DEV48, DEV60), DEL (DEL48, DEL60), CL (CL340, CL460, CL580) and CV (CV340, CV460, CV580) Filters.

Installation: In order to replace this product, take out the old Hayward Air Release Assembly. Clean out any dirt or debris you may notice and insert the replacement air relief assembly. Lubrication on the exterior orings is recommended but optional. Lubrication is not included.

Compatible: This manual air relief assembly is compatible with all Hayward Pro-Grid DE (grids) filters, Swim Clear and Swim-Clear Cartridge Filters

Compatibility: This air relief valve works with all FNS, FNS Plus, SMBW 2000 Series and 4000 Series, Clean and Clear (ccp100, ccp320, ccp420, ccp520), Quad DE 60, 80 and 100 and all Predator Filters.

Compatibility: 188592, 188593, 188594, 160316, 160317, 160318, 160301, 160332, 011555, 147411, 180007, 180008, 180009

Made to Work With All Automation Systems: This actuator is made to work with all major brands including Pentair, Jandy/ Zodiac and Hayward Automation Systems. Systems include but are not limited to Pentair EasyTouch, EasyTouch PSL4, Compool, Intellitouch, Jandy Zodiac iAqualink, Aqualink PDA, Aqualink RS, Aqualink Z4, Hayward OmniHub Smart, Omni Logic, OmniPL, ProLogic, AquaPlus, OnCommand, Automation Systems and Intermatic

Identifying The Problem: One of the most common problem with Swimming Pool Automation Valve Actuators is the failure of internal gears. Over time the gears start weaing out and the valve is not able to rotate anymore. Another common problem could be the motor going bad.

Perfect Fit: Custom molded to fit directly into the Whisper flo and Intelli flo pool pump. 2 inch fitting will make your plumbing work fast and easy.

2 Inch Connection: These Hi Temperature Unions are made for 2 Inch PVC pipe. The threaded end is designed to fit into a 2 inch female threaded pool pump

Included - Tension Clamp, Washer, Spring Barrel Nut Assembly. Measurements are approximately 23-1/4-inch length by 2-1/4-inch height by 22-1/4-inch width

Easy fit - The Swimables tension clamp is made for an easy fit as well as an easy screw on knob.

🌊 Made to Fit ANY SIZE Pool Plumbing: The Swimables Backwash Discharge hose is 2.5" and fits 2" as well as 1.5" plumbing. It is compatible with Pentair, Hayward, Jandy, Waterway, and other pool filters as well as their backwashes. While other backwash hoses need to be stretched and most times do not fit, Swimables Backwash Hose slides right onto the pipe.

💰 Exceptional Quality: The Swimables Backwash Discharge hose is made to last in the toughest weathers and conditions. Traditional blue backwash hoses often times burst under high pressures and tear on sharp edges or grasses, the Swimables Hose is made to withstand any of those. With 1.2mm thickness, it will survive in any harsh condition.

🌊 HOW TO TEST: If you suspect the thermal regulator to be faulty simply place the thermal regulator in water heated to at least 130 degrees Fahrenheit. The regulator should open

🏊 HOW TO FIX: If the thermal regulator does not open during the testing stage, replace the thermal regulator. If it is found that the theral regulator IS working then proceed to Internal Bypass.

Made To Work With Select Pentair Heater Models: The Igniter with Gasket Kit is compatible with Pentair MasterTemp Heaters and Sta-Rite Max-E-Therm Heaters

Identifying the Problem: Open up your Pentair Mastertemp or Starite Maxetherm Heater and locate the Igniter. The igniter can be found via the heater's back access pane. There are two things that could be wrong with the igniter, first being shattered and second being burned.