Industrial & Scientific From RATTMMOTOR on Amazon

【Description】The tool setting instrument is a special tool setting instrument for the engraving machine machining center machine. The output signal of the tool setting instrument is received by the numerical control system and then the tool length setting, tool wear detection and tool breakage are detected by the program control. In the case of no vibration and malfunction, the thermal deformation of the machine can be corrected according to the rated voltage and current and the specified speed.

【Parameter】This is a normally closed 4-wire high-precision tool setting instrument with a stroke of 5mm. The positioning accuracy is 0.001mm, the contact life is up to 3 million times, the contact force is 1.5N, and the contact rating: DC24V 20mA.

♞【Motor specifications】Holding Torque:3N.m; Current:5A; Phase:2; Size:60x60x88mm; Step Angle(degrees):1.8 degree; Motor Lead Wire: 4-wire; Encoder lines:1000

♞【HSS60 Driver】2-Phase Hybrid Stepper Servo Driver; Frequency:0-200KHz; Insulation resistance:>=500MΩ; Voltage: DC 24-50V input;

♞【Nema23 Stepper Motor】 23HS8430B Nema23 Stepper Motor / Holding Torque: 270 oz-in ; 180N.cm / Motor Size:57x57x76mm / Phase: 2 phase / Motor Lead : 4-Lead / 1.8° Step Angle / Type:Hybrid

♞【Stepper Motor Driver】TB6560/MD430 Stepper Motor Driver / Current: 3A / Support voltages : 12-34V DC / Step frequency up to 100khz / 2 phases bipolar driver / Full step, half step, eight step and sixteenth step

♞【Brief introduction】The RMHV3.1 is a 4 axis motion controller,the highest uniaxial output pulse is 500KHz and the pulse width can be adjusted.This provides high control precision for stepper motors and servo motors.The operates as a stand alone system without the need of a computer.

♞【Compatible with G code set】4.3 inches TFT Screen ; Resolution ratio: 480x272 ; The CNC MOTION SYSTEM Controller can be finished only by 17 keys and it supports the FANUC with high universality to be compatible with G code set.Support the USB flash disk to read the G code,and the size of G codefile has no requirement;

♞【Nema23 Stepper Motor】Step Angle: 1.8°; Current: 3.0A; Holding torque: 425oz-in/ 280Ncm; Shaft: Dual Shaft,Shat diameter: 8mm; Wirings: "A+"=Red / "A-"=Green / "B+"=Yellow / "B-"=Blue

♞【FMD2740C Driver】Input Voltage: DC18-50V; Current: 1.4A-5.6A;Subdivision precision: 400,800,1600,3200,6400,12800,25600,1000,2000,4000,5000,8000,10000,20000 and 25000 optional

【Compact Structure】The base is 2080 profile, the tail end bearing piece, front end is equipped with Nema23 stepper motor and the flange piece connecting the motor, with the load-bearing slide table, the 1605 lead screw and the coupling, adding a stable bearing, and the double optical axis design. Working Length: 300mm/11.81inch.

【Flexible Installation】80mm aluminum profile base, M4 movable nut at the bottom, side mounting groove for easy fixing, M3 nut can be installed with limit, easy to install. This linear stage can be used in combination with multi-axis, horizontal cross, gantry type, three-axis type, four-axis type, etc.

✅【Upgrade Version CNC 3018 PRO】Frame size: 40x33x24CM. Working area: 30x18x4.5CM. Material: Aluminum Alloy. Spindle: 775 spindle motor (12-24V) 24V:10000r/min. Stepper motor: 42 stepper motor, 12V, phase current 1.3A, phase resistance 2.1 ohms, torque 0.25N.m

✅【Simple Assembly/Use】This mini cnc router machine kit is mainly designed for DIY carving enthusiasts/beginners, easily assembled and opertated, coming with a paper manual and USB flash drive of all the files.

【How to Connect Spindle Motor and VFD】The spindle motor's aviation plug marked with number 1, 2, 3, 4. Number 1, 2, 3 port are connected separately with inverter's port U, V, W. Number 4 is the ground wire, no wiring is required.

【2.2KW Spindle Motor】: ①This is a 220V-2.2KW water-cooled 8A Φ 80x195mm spindle motor come with a ER20 nut and collet. Frequency is 400HZ, 0.005 accuracy and runout off is less than 0.01mm.

♞【Nema23 Stepper Motor】Step Angle: 1.8°; Current: 3.0A; Holding torque: 425oz-in/ 280Ncm; Shaft: Dual Shaft,Shat diameter: 8mm; Wirings: "A+"=Red / "A-"=Green / "B+"=Yellow / "B-"=Blue

♞【FMD2740C Driver】Input Voltage: DC18-50V; Current: 1.4A-5.6A;Subdivision precision: 400,800,1600,3200,6400,12800,25600,1000,2000,4000,5000,8000,10000,20000 and 25000 optional

【Spindle Motor Parameters】The 1.5KW air-cooled spindle motor's 220V, 400HZ frequency, less than 0.05mm runout off, 0-24000RMP speed. It should be noted that the spindle speed must be kept above 9000 rpm, otherwise the spindle will be damaged.

【Spindle Motor Features】This spindle is designed with a dustproof and waterproof cover, the body is made of stainless steel, and the rear is equipped with a cooling fan, which is of high quality. In addition, it contains 4 bearings, high-precision grinding taper hole, high-precision, low noise.