20 Best-Selling Electronics From OONO
Top 1
Ultra-Small RPi GPIO Status LED & Terminal Block Breakout Board Module for Raspberry Pi
OONO
D-1480
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W, Zero-2W.GPIO status LED and power 5V / 3.3V indication. GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO.
Top 2
24/20-Pin ATX DC Power Supply Diagnostic/Breakout Board Module
OONO
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header. With latching button switch to control ATX power supply output ON/OFF.Total 16 LEDs, it is convenient for you to diagnose the functions of all pins except COM/GND, therefore, if the output of any one wire of your ATX power supply is faulty, it can be seen at a glance.
Top 3
Ultra-Small RPi GPIO Terminal Block Breakout Board Module, for Raspberry Pi
OONO
MD-D1352-1
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
The item has been soldered and assembled. Support for Raspberry Pi 1 Model B+, Pi 2 Model B, Pi 3 Model B, Pi 3 Model B+, Pi 4 Model B, Pi Zero, Pi Zero-W.Terminal block pitch 2.54mm/0.1", wire size range 28AWG to 18AWG, strip length 4.5mm, screw M1.6 steel, pin header and cage copper.
Top 4
Semi-Enclosed Enclosure Kit for Raspberry Pi BeagleBone Arduino UNO Mega
OONO
CASE-048-1
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
This is a multi-purpose semi-enclosed enclosure kit, Supports Raspberry Pi 1 Model A+ / Pi 1 Model B+ / Pi 2 Model B / Pi 3 Model B / Pi 3 Model B+ / Pi 4 Module B / Pi Zero / Pi Zero W, Arduino Uno R2 / Uno R3 / Mega 2560 R2 / Mega 2560 R3 / MKR Series etc, and BeagleBone / BeagleBone Black / BeagleBone AI / BeagleBone Black Wireless / BeagleBone Green / BeagleBone Green Wireless or SanCloud BeagleBone Enhanced.It can be assembled very flexibly as a semi-closed enclosure, or as a two-layer bracket, or if you buy multiple sets, it can be used as a Raspberry Pi cluster case.
Top 5
Screw Mount 2 x 8 Position Banana Jack Distribution Module, DC Power Strip
OONO
D-1375P
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Screw Mount 2 x 8 Position Banana Jack Distribution Module. Support for multiple module extension connections.A and B position termianl blocks, maximum current 30 Amp (each position). Pitch 7.62mm/0.3", Wire range 26AWG ~ 10AWG / 4.0mm square, Strip length 8mm. Screws - M3,steel, Cr3+ Zn plated. Pin header and Cage - Brass.
Top 6
RPi PoE Relay Board Module for Raspberry Pi 3B+ 4B
OONO
D-1397
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Supports Raspberry Pi 3B+ 4B, the RPi Relay Board gives your Pi the ability to control high voltage/high current devices, easily makes normal home appliances become intelligent. And support 802.3af Power-over-Ethernet (PoE) from Raspberry Pi gigabit ethernet port, allows you to power your Raspberry Pi using Power over Ethernet–enabled networks.Power-over-Ethernet (PoE): IEEE802.3af compliant. Support PoE applications in both of Fast / Gigabit Ethernet environments. Fully isolated switched-mode power supply. Support wide input voltage range 37Vdc to 57Vdc. output 5V/2.5A
Top 7
Rocker Switch Thermal Circuit Breaker Overload Protector 4 Channel Power Distribution Module DIN Rail Mount
OONO
4.7638 x 3.8189 x 2.126 Inches
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Input voltage AC 125/250V 50/60Hz. Maximum total input current 40A(one position terminal block maximum current 20A).Maximum output current 10A(one channel). Maximum total output current 40A.
Top 8
32PCS 4 Colors 30/45A Quick Connect Disconnect Power Connector Assortment Kit
OONO
TB-KIT26-1
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
8x Standard Red Housing. 8x Standard Black Housing. 8x Standard Wihte Housing. 8x Standard Blue Housing.24x 30A Silver Plated Power Wire Contacts, Wire range: AWG 16 - 12 / 1.3 - 3.3 mm square.
Top 9
RPi Step-Down DC-DC Converter HAT for Raspberry Pi, with Terminal Block GPIO Breakout
OONO
D-1435
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Support input DC 6.5 to 32V(from blue terminal block), Output DC 5V to Raspberry Pi, Output maximum current 3 Amp, Conversion efficiency 90%.If your power supply system is DC 12V or 24V, then you can use this HAT module to conveniently conversion to DC5V to provide power supply for your Raspberry Pi, and these screw terminal blocks are very convenient for GPIO breakout connects. The module can support Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B (of course, Zero and Zero-W can also be supported, but only two screw holes can be fixed).
Top 10
Terminal Block Breakout Board Module for Teensy 3.2, Screw Mount Version
OONO
D-1389 to D-1395 Series
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Terminal Block Breakout Board Module for Teensy 3.2, Screw Mount Version. With the breakout board, you can easily extend Teensy 3.2 projects to industrial control, home automation or other applications.With 107 DIY solder pads on board, pitch 2.54mm, hole 0.8mm, you can use these pads to install soldered some electronic components for you need.
Top 11
Best IO Modules
RPi 3.3V to 5V 26 I/O Bidirectional Voltage-Level Shifter Module for Raspberry Pi, Logic Level Converter
OONO
D-1433
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
The module can support Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B (of course, Zero and Zero-W can also be supported, but only two screw holes can be fixed).Support RPi I/O 26 ports 3.3V to 5V bidirectional logic level conversion(input or output). But not include ID_SC and ID_SD ports(since ID_SC and ID_SD are used to identify HAT modules, these two ports are not connected to the 5V interface).
Top 12
Edge Connector IO Breakout Board for BBC Micro:bit, Microbit Breakout Module
OONO
MD-D1329-1
0.2205 Pounds
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
15 connect holes for 3V, GND and 9 I/O ports(include IIC and SPI), you can easily connect alligator clip lines.Pin header connected all I/O ports, 3V and GND. 19 Red pin header terminals all connected 3V. 19 Black pin header terminals all connected GND. 19 Yellow pin herder terminals connected all I/O ports, P0 ~ P16, P19 and P20.
Top 13
Low Loss PWRshield LVD-HVD Power Guard Module, PWRguard
OONO
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
The PWRshield module is a programmable LVD(Low Voltage Disconnect) and HVD(High Voltage Disconnect) power protect system. Programmable voltage setting for LVD and HVD(rocker switch set to AUTO). With emergency ON or OFF function, if you want switch output to be immediate and remain ON or OFF, you can set rocker switch to ON or OFF.Design based on microcontroller and low loss MOSFETs (on status resistance < 0.002 ohm), you do not have to add heatsinks even for 30 Amps of continuous working current.
Top 14
Best for Image Processing
GPIO Status LED Terminal Block Breakout Board for Raspberry Pi A+ 3A+ B+ 2B 3B 3B+ 4B
OONO
MD-HD040-1
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
GPIO status LED and power 5V / 3.3V indication.GPIO output or input level high LED on, output or input level low LED off. 5V blue, 3.3V red, GPIOs green. The position of the LED is in a one-to-one correspondence with the position of the Raspberry Pi 2x20pin connector, and the logic level of the GPIO can be observed very quickly and intuitively. The driving current of each LED is only 0.1mA, so you don't have to worry about it affecting the read and write status of GPIO.
Top 15
Banana Jack 8 Outlet DC Power Distribution Strip (with Cable)
OONO
F-1028/F-1043 Series
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
F-1028 DC power distribution outlet strip are heavy-duty power distribution strip. 8 position + and - banana jack output.Operating voltage: 0 ~ 60VDC. Maximum allow input current: 50 Amp. No-load current: 0mA. Maximum output current for each position: 24 Amp. Total maximum current 50 Amp.
Top 16
OONO Whole House Audio Stereo 8-Zone Speaker Distribution Module
OONO
MD-D1342P-1
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Parallel connecting block for use with Impedance matching volume controls. One Stereo Input, eight stereo outputs. Detachable connectors for easy wiring. (NOTE: Must be used with impedance matching volume controls)The item for 70V / 100V constant voltage audio power amplifier, maximum input 300 Watts(per channel).
Top 17
OONO ATX 24/20-Pin DC Power Supply Breakout Module with 2.1A USB Port
OONO
F-1036
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
24-pins Standard ATX Connector, support 20 / 20+4 / 24 pins wire header.Stand-By and Power-ON indicator LEDs. With latching button switch to control power output ON/OFF, it also supports external latching switch control power output ON/OFF(when using an external switch, the switch state on the module must be set to OFF)
Top 18
8 Channel Connector Power Splitter Distributor Source Strip, with 8 Independent Control Switch
OONO
F-1039
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Operating voltage: 6 to 20VDC, No-load quiescent current: 2.7mA(at 13.8V).Input port: maximum input current 40A, with a 40A fuse. Output port: 8 output ports, each port has an independent toggle switch and a power-on LED indicator, each port maximum output current 20A.
Top 19
Banana Socket GPIO Breakout Board for Micro:bit Microbit
OONO
D-1383
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Banana socket GPIO breakout board for Micro:bit.This is a very useful GPIO breakout board, using banana plugs to easily connect GPIOs of Micro:bit, for learning, education, laboratory, electronic engineering debugging, etc.
Top 20
Screw Mount 2 x 4 Position Banana Jack Distribution Module, DC Power Strip
OONO
D-1376P
Ratings for OONO (CPR Score)
Seller | CPR Rank | Amazon Fulfilled | Prime | Free Shipping |
---|---|---|---|---|
Electronics-Salon. | - | ✅ | ✅ | ✅ |
Features
Screw Mount 2 x 4 Position Banana Jack Distribution Module. Support for multiple module extension connections.A and B position termianl blocks, maximum current 30 Amp (each position). Pitch 7.62mm/0.3", Wire range 26AWG ~ 10AWG / 4.0mm square, Strip length 8mm. Screws - M3,steel, Cr3+ Zn plated. Pin header and Cage - Brass
Featured Reviews Related to OONO for Electronics
61,993 Reviews Analyzed
6,806 Reviews Analyzed
8,521 Reviews Analyzed
2,000 Reviews Analyzed
910 Reviews Analyzed
629 Reviews Analyzed
5,775 Reviews Analyzed
676 Reviews Analyzed
14 Reviews Analyzed
Electronics OONO Pricing
- Avg.Price: $31.26
The price range of $17.00 to $98.00 form our top picks.
Similar Brands Like Electronics OONO