Tools & Home Improvement From O'SKOOL on Amazon

Package : 1PC

Package Included: ●1x vacuum switch with 15'' power cord ●1x Installation instruction

Suitable for most medium duty workloads. Perfectly suited for medium-sized work loads such as most Miter Saws, Table Saws, Power Sanders and Routers, and extend the life of your vacuum.

The total current of all electrical appliances used with this device must not exceed 15A when operating, and the electrical cutting tool can only be used at the TOOL socket and cannot be used by inserting it in the VAC socket.

Rubber boot 4" ID (inside diameter) and a hose clamp fit a 4" OD (outside diameter) power tool port.

ABS plastic port is tough and wear-resistant, which can extend the use time.

Rubber boot ensures tight fit, even variations in port size.

The steel block and clamping screw handle securely tightens the tools like a vise, and the fine thread spacing of screw handle provides uniform and stable clamping pressure for clamping the workpiece. The jig with rugged aluminum sides holding work securely without damage to the wood.

The drilling bushing is made of high-quality materials, with high strength and accurate positioning. When using a hand held drilling machinel, the countersunk drill bushing allows the drill bit to slide into the hole easily, ensuring the correct angle of the drill bit.

There are 4 holes along the top of the jig, only 2 of the holes accept threaded bushings(Replaceable 1/4" 3/8" 5/16").the other two holes accept 7/16" and 1/2" drill bits.

【 Color-coded 】 There are five colors on the edge of the mesh sandpaper, and different colors are used to indicate the grit. Pink: #180; Green: #240; Orange: #320; Blue: #320; Purple: #600.

【 Material 】Made of a lightweight, strong meshed polyester nylon material combined with tough aluminum oxide abrasive. Both sides of the mesh sandpaper can be used.

【Application 】Use for fine sanding on lathes, or any detail woodworking projects such as turning spindles, pens, and moldings; Mesh sandpaper works on wood, composites, metal, plastics, acrylics, paints, primers.

Rubber boot(4" inside diameter ) and a hose clamp fit a 4" outside diameter power tool port.

ABS plastic port is tough and wear-resistant, which can extend the use time.

Rubber boot ensures tight fit, even variations in port size.

The Remote Control is capable of controlling multiple units of Dust Collector Remote Switch at the same time. They are suitable for use with a variety of appliances such as vacuum, dust collector, power feed, work lamp, etc. The Remote Control signals can penetrate walls. If not blocked, the signals travel as far as 50 meters.

Package Included: *Automatic Vacuum Switch with 6' Power Cord X 1; *Remote Controller X 1; *CR2032 Coin Battery X1 (The battery is included in the remote control); *Installation Instruction X 1

Input Voltage 120 volts AC. Maximum 15 amps; maximum horsepower 2.4HP. The Remote Control Switch is soft start mode,when click the remote control's ON/OFF button, the dust collector will start automatically. And the dust collector reaches to its full speed in 3 seconds after being turned on.When the work is completed, click the remote control and the dust collector keeps running for 2-3 more seconds before it shuts down.

The pins on the miter clamp bite into the wood to keep it in place. It does leave a few dimples in the edge of the wood, but so would spring clamps or nails, you just fill those hole.

The jig's unique cam design exerts such pressure on mitre joints that wood piece can be hauled around by one leg immediately after gluing. You get a perfect glue joint as in glue joint with our miter clamps.

Package: 1pc

The patented design of this sanding drum eliminates the need to buy replacement sanding sleeves. Cut and fold any type of sheet sandpaper to size for the particular drum size you're using. The item makes it easier and faster to replace sandpaper.

The sanding drum body is made of plastic and covered with TPR. It feels comfortable in use and has a small swing, which makes the work more accurate and efficient.

Suitable use sanding holes, contouring edges, and buffing out irregular shapes and buffing out irregular shapes. Simply chuck the 3/8" spindle into a portable electric drill, cordless drill or air powered drill for two-handed control.

Easy to change temperature setting,touch of a button can changed from °C to °F, you can change °C /°F by holding the (ON ⁄ OFF) & (°C /°F) button for about 3 seconds.

Ergonomically handle design and using specially-designed tips for fillets, curves, and corners,easy access to tight corners.

The sock protect your covering and the coating on your heat sealing iron and prevents scratching and marring.