Automotive From HIYAZONE on Amazon

HOW TO INSTALL: 1.Clean the pre-installed position,make sure the position is clean and dry before you install. 2. Measure the length of tail in need.3.Cut off excess length,heat it if possible. 4. Use the adhesion promoter(wipe paper) to wipe the pre-installed position,then waiting about 10 seconds. 5. Tear the cover of the glue of one end of car wheel rubber strip then stick on car. 6. Tear more cover of glue slowly and stick it on car slowly with strength.

FUNCTION:Exterior wheel tyre fender protective and decorative accessories,them prevent collision hurts on the wheel tires and car

WIDE COMPATIBILITY:The car universal fender flares suitable for all car vehicle,makes your car better show 3D vibrant after installation

SIZE:Total length is approx.4.9 ft/1.5meter,more specifics of size please check on pictures,thanks!

FOR BETTER EFFECTIVE:please used a heat gun or hair dryer to heating up the Tape or Glue;they go on easy if you heat up each section of the rubber before install.【if pursuit more higher adhesive quality please strengthen the fender flares by car glues(not included),it's better use adhesive remover((not included)) while disassemble the auto fender flares,normally Not Recommend this way if you has last solution.】

EASY TO USE:Easy to mounting, on back with glue so you can directly to peel and stick.

WIDE APPLICATION:The hood scoops personality modification to decorate car,fit for most of popular cars.

STEPS TO INSTALL: 1.Clean the pre-installed position,make sure the position is clean and dry before install 2.Tear the cover of glue of car side mesh vent then stick it on your car.

TIPS FOR PREVENT SIDE VENT FALL OFF: 1.Please install the car side hood vent decor in good weather day or warm indoor. 2.Follow installation instruction. 3.Leave the car alone for at least 24 hours after install the car side vent accessory.4. it would be better if use a heat gun or hair dryer to heating up the tape or glue before apply!

【WATERPROOF】High-density waterproof material, water directly condenses into water droplets on the surface

【DECORATION&PROTECTION】The car trunk spoiler lip can be used for pressure tail, top wing, front stalls spoiler glass.It can fit perfectly according to the original car range and make your car looks great

【HOW TO INSTALL】1.Clean the pre-installed position,make sure the position is clean and dry before install. 2.Measure the length of tail in need. 3.Cut off excess length if too long,heat it if possible. 4. Use the adhesion promoter(wipe paper) to wipe the pre-installed position,then waiting about 10s. 5.Tear the cover of glue of one end of universal spoiler and stick it on car,then tear more and stick it from one end to another.6.Put on the 2-end sleeve ,them can be perfectly closed

【FOR BETTER EFFECTIVE】please use a heat gun or hair dryer to heating up the Tape or Glue;they go on easy if you heat up each section of the rubber

【TIPS TO PREVENT CAR SPOILER FALL OFF】 1.Please install the car spoiler in good weather day or warm indoor. it would be better if use a heat gun or hair dryer to heating up the tape or glue;they go on easy if you heat up each section of the rubber.(HIGHLY RECOMMEND) 2.Follow installation instruction. 3.Leave the car alone for at least 24 hours after install the car universal spoiler.

Snow shovel: ABS high strength plastic casting forming, hard and durable,low temperature resistance

Expansion aluminum rod, adjustable length, easy to clean ice

Package content:1*car snow shovel

【Easy to install】No need to paste,just stick directly to the gap on the line.

【Stable & Strong】The car rubber strip is strong toughness and stable, not easy to be destroyed and it can be used for long time.

【Universal】Our Auto Edge Trim Rubber is universal ,can use for most popular cars.

The Auto Sun visor phone holder is very convenient to use.

Fit for most of popular cars,enjoying your driving

Package content:1 x Car sun visor Holder

Video Output:1.0Vp-p/ 75Ω;View Angle:170°

Working Voltage:DC9V-12V±0.5V;Camera Waterproof Rate:IP67

Friendly Note:the car reverse monitor can be connected to a voltage range between 12-36V,but camera could only be connected to 12V,if you wiring with voltage over 12V,the camera may get burnt.Thanks for understanding

Wide compatibility:The car fender suitable for all Car vehicle,makes your car better Show 3D vibrant after installation .

Material: the auto fender flares made from high strength soft rubber,easy to deform.

Size:Total Length is approx.4.9 ft/1.5meter,more specifics of size please check on pictures.

Useful Car Cleaning Mitt:Combination of special nano-ingredients with the pneumatic polisher produces the best cleaning result with surface, speed and amazing cleaning ability

More Convenience:Can be used to substitute wax abrasives or traditional clay bars which can be inconvenient to use

Warm Tips:Please kindly read the cautions and instruction in description!!!

Multi-Protection:The power supply transformer with over-voltage Protection,overload Protection, LED indicate light ,low temperature and prevent short circuit,which all ensure safe

Package Note:No installation instruction/wiring cable/on&off switch/screws come with,Only Power Converter Adapter

Warm Tips:Please DO NOT let the unit work long time over rated current!Don't store any combustibles near the item!The item is only for indoor use!please do not touch it during working!!!