Industrial & Scientific From HICTOP on Amazon

3.This silicone sock speeds up the heating of the heat block and keeps the temperature stable while printing.

4.It prevents sticky filaments from sticking on the hotend and extends the life of the hotend

5.It perfectly fits the E3D volcano hotend and easy to install.

3.The size of resin spring steel plate is 5.3X3.15inch(135X80mm). Suitable for any DLP light-curing 3D printer with a printing platform size of 135X80mm, such as: Anycubic photon, photon S, Photon Mono, Photon Mono SE, Qidi Shadow 5.5S, please confirm the printing platform size of your resin 3d printer before purchasing

4.Please adjust the z limit switch after installation according to the instruction.

5.2 pairs a pack, then you can continue your print as soon as you take the before one out. It helps to save your time.

3 Excellent adhesion can be achieved when the temperature of the heated bed is about 60℃, you can print directly on each side of the double sided PEI sheet without using any glue or other tools to help the model to stick onto the sheet. You do not need to worry about the prints curling with a 60℃ bed temperature.It also can print PETG very well, but the temperature of the hotbed needs to be about 80-85℃

4 Prints come off the surface easily when the temperature of the heated bed reaches room temperature. If the print is still stuck, gentle flexing of the plate will help remove it.

5 The size of HICTOP PEI bed is 235*235mm（9.25*9.25inch）, it is applicable with Creality 3D printer such as Ender-3 Pro, Ender-3 V2，Ender-3, Ender-3S, Ender-3X, Ender-5, Ender-5 Pro，CR-20, CR-20 Pro and similarly sized machines.

There is a 2 pin female connector on the thermistor for 3D printer

Wire length for the 100K thermistor 3d printer: 1.2m/47.2 inches.

Recommended parameters for the thermistor: R25℃=100K B25/50=3950K± 1%

3 It is a complete upgraded hot end for the Artillery Sidewinder X1, it's all there with a quilting motor, thermistor, heater cartridge, circuit board, LED circuit board, complete hotend and heating sock.

4.Direct drive extruder, great support for flexible filament.

5 The PCB on V1 is a little bit different, so it does not compatible with that version, V2, V3, V4 all are OK, please feel free to purchase.

3 All the parts you need to upgrade ender 3, ender 3 pro, ender 3 V2 to dual Z rods are included in the box.

4 Compatible with Creality ender 3, ender 3 Neo, ender 3 pro, ender 3 V2, ender 3 V2 Neo 3D printers

5 There is a full metal plate to lock the power supply, we are sure that you will like this design.

Application of the 24v heater cartridge 40W: Creality ender 3, ender 3 Pro, ender 6 CR-10S Pro etc. 3D Printers Prusa Mendel

Diameter of the ender 3 pro heater cartridge : 6mm. Length: 20mm,Wire Length:1m/39.4inch

Temperature of the ender 3 V2 heater cartridge: It can take up to 280 ° C

3 Fit for: Creality CR-10, CR-10S, CR-10 Mini and similar 3D printers

4 Stable Material: Aluminum, stainless steel, brass and MK8 nozzle

5 Extruder kit : cr-10 hotend with thermistor, heater carriage, and two cooling fans.

3 With 1m 100K thermistor and 24V 40W heating carriage, 0.6m blue high temperature resistant Teflon tube

4 Working temperature: -20-260℃

5 Material: Aluminum & Stainless Steel & Brass